How to install kung Road Ranger

Content

• Preparation for installation of kung
• Unpacking procedure
• Electricity connection
• Body preparation
• Installing the Road Ranger kung
• Reasons to buy a kung on a pickup truck

Owners of pickup trucks, who are thinking about finishing their iron horses, have definitely heard more than once aboutkungas of the company Road Ranger. They are known in the automotive environment for their high quality and durability. Before you buy, though, it's a good idea to learn how to install a Road Ranger kung.

This manufacturer specially develops hardtops for specific pickup models. Therefore, they always fit well into the design of the car and are easy to install. The action algorithm is common to most brands. Let's consider the process using the example of a popular pickup truckVolkswagen Amarok 2010-2022.

Preparation for installation of kung

A great choice for this SUV will bekung Road Ranger RH04 Profi 1900891. Compared to the base model, it has useful options such as:

• Side windows made of GPR plastic that open upwards;
• Connection to the car's central lock;
• Interior decoration with carpet;
• Illumination;
• Rear window heating;
• Gas shock absorbers.

Before proceeding with the direct installation of the kung, it will be necessary to unpack it and prepare the car body.

Unpacking procedure

The product is delivered in a cardboard box with wooden frames, which is tightened with packing tapes.

1. Prepare a place in the workshop and carefully lay the box horizontally.

2. Cut the ties, lift the cardboard cover of the box.

3. Disconnect the frames and other elements of the box.

4. Carefully remove the packaging directly from the kung and carefully inspect it for scratches and damage.

5. Everything necessary for installation, including instructions, is under the kung. Therefore, it is necessary to lift it and get the components. Keys are fixed inside the kung.

6. Make sure you have a complete set using the list in the manual.

Electricity connection

Unpacking is followed by preparation of the wiring for connecting the electrical equipment of the kung.

1. Remove the battery terminal. This will prevent errors in the car's electronics.

2. Carefully dismantle the brake light on the pickup cabin and disconnect it from the on-board network.

3. Install a plug with removed electrical wiring in place of the stop light.

4. The wiring must be pulled through the interior and connected according to the instructions for your car.

Body preparation

In order for the kung not to damage the paintwork of the pickup, the contact points should be covered with protective film. It comes in a set. It will also not be superfluous to make sure that a sealant is glued on the entire lower surface of the kung.

1. Clean the body from dirt and debris, then close the door.
2. Thoroughly wipe and degrease the surface of the sides that will come into contact with the hardtop. Including the rear.
3. Apply the protective film, cutting off the excess with scissors. Make sure it fits snugly against the LFP.

It is important that the body is not deformed. If everything went well, you can start installing the product.

Installing the Road Ranger kung

It will be extremely difficult to do everything yourself without damaging anything. Therefore, the work should be carried out by at least two people.

The procedure is as follows:

1. Carefully place the kung on the sides so that its seal fits snugly against the armor film. There should be no gaps.

2. Pull the wiring from the plug of the additional brake light into the trunk.

3. Climb inside the kung and connect the electricity.

4. Install clamps between the sides and the kung, but do not tighten them. The kung must be fixed only after the clearances have been set.

5. Clamps must be tightened in a staggered order, starting from the cabin. The first on the left, the second on the right opposite her, the third again on the left, etc.

6. Install rubber seals on the rear door opening.

7. Screw the terminal to the battery and test the operation of the lock and the electrics of the kung.

Reasons to buy a kung on a pickup truck

Installing a kung is one of the most popular tuning options for a pickup truck. This element of the exterior performs both a practical and an aesthetic function. Increases the practicality and functionality of the car, as well as gives its appearance a more finished and harmonious look.

Plastic cabins from Road Ranger are able to please not only with a beautiful design, but also with excellent tightness, durability and a wide range of options. The site features many kungs of this brand at good prices, including the RH04 Profi. You can also equip the kungan additional roof rack.

If you want to trust professionals, ourstuning studiowill be happy to help finalize your SUV.Specialists of the Vnedorognik workshop can install a kung on your car in a few hours.Contacts.

You can download the installation instructions for the Road Ranger RH04 on the Volkswagen Amarok pickup here