How to charge a car battery?

Most drivers, regardless of whether they care for car service or not, at some point face a discharged battery. Calling a car service and delivery to a repair shop can take a lot of time and money, and this may not be the best option for everyone. You can save time and money if you learn how to charge the car battery properly by completing some simple actions from the battery that will be discussed today.

Attention : working with autoacmulators can be dangerous and you can damage your car if you are wrong. Please be careful when working with a car and always contact the car manufacturer.

Step 1: Prepare a car battery

the first step in studying the charging of a car battery is to prepare it. You need to determine whether you need to remove the battery from the pallet or whether it can be charged as it is.

Technically all car batteries can be charged without removing, but before charging it will not hurt to quickly clean the battery.

Turn off automobile electronics

After preparing the car battery, the car engine must be switched off. Then turn off the entire electrical system of the car, including the lighting of the salon and multimedia device . Make sure all power is off before you start the next step of the charging process.

Step 2: Disconnect negative and positive cables

Be sure to first disconnect the negative and then a positive battery terminal cable . Otherwise, you can cause short circuit or damage a car's battery.

negative cable - almost always black with " - " symbol. A positive cable is usually red with a "+ " symbol. To disconnect each cable, you may need to first remove the plastic caps, which are sometimes located on the terminals of the car battery.

For most car batteries, you need to use a 10 mm face key to weaken the negative cable, and try to keep it away from the positive cable as the charge can be transmitted between two sources. Finally, repeat the process with a positive cable and a clot, trying to keep them separately from each other.

Step 3: Clean the battery terminals

It is important to clean the car battery terminals before charging a car battery. We recommend using a brush for cleaning terminals, which in shape and appearance is similar to a toothbrush (it can also be used in the absence of the first). The terminal cleaning brush is used to clean the battery terminals of corrosion debris and chemicals.

cleaning brush in paired with commercial batteries, but a mixture of baking soda and water will be just as effective to neutralize acid, prevent corrosion and prevent any possible malfunction. We recommend the ratio of one cup of distilled water and one tablespoon of baking soda.

Step 4: Connecting a charger for car battery

• Make sure the car charger is off.
• First, connect the positive cable to the positive terminal, then connect the negative cable to the negative terminal in the same order.
• Turn on the car charger and set the charge speed to the minimum possible level.
• If the charger is equipped with a timer, install it for the appropriate period of time. If the charger is not equipped with a timer and you do not know how to charge a car battery for a long time, consult a user guide or search for information on the Internet to avoid possible recharge.

Disabling the charger for a car battery

To complete the charging process of a car battery, turn off the charger before touching anything else. After switching off the charger, just disconnect the positive cable first and then the negative.

Be sure to replace the cables at the terminals of the car battery. And again, do not forget to connect the positive cable before the negative. If you have completely removed the car battery, it is time to install it back into the mount.

Shag 5: Verification of automobile battery

There are two types of chargers :

• standard car chargers;
• Starting devices.

smart chargers such as Battery Tender and Ctek MXTS CRIULY , can be useful in the situation. The charger will help you charge the battery and return the car to operating status.

How to charge a sitting car battery?

1. Prepare Auto-accumulator .
2. Disconnect negative and positive cables.
3. Clean the battery terminals.
4. Connect the charger for a car battery.
5. Test your car battery.

Can I use the starting device as a charger?

No, the starting device cannot be used as Charger .This is due to the fact that the starting devices are intended for instant, but still a powerful surge in electricity to switch on the car battery. Once the battery is started, the battery charging process takes over the AC generator.

Can I just charge the planned battery?

You can either use a car battery charger to charge the discharged battery, or connect to the operating car battery, to charge the discharged battery. If you have an old battery that has been used for over three years, it is time that it is time to buy a new auto part store.

When charging a car battery which terminal is connected first?

When charging a car battery, you must first connect to a positive terminal. Then connect the negative terminal. If you connect to the wrong terminals, you can damage the car battery or even blow it up.

Subscribe to our social networks